Repairing Tile Grout Helps Stop Water Damage

When the grout between the tile in our bathrooms becomes cracked, loose, or missing, water is allowed to get underneath the tile and damage the wooden floor underneath it. This damage can eventually become structural and cause the need for replacement of the entire floor or at least a sizeable portion of it. This will not only cost you quite a bit of money, but will also cause the loss of at least a day or two in repairing it. Not many people want to have to tear up the tile on the floor in the bathroom or on the walls of the shower and then tear up the floor, too. Repairing grout is not a difficult job to do and it is something that you can do yourself to keep your floor waterproofed.

There are a few different kinds of grout that you can use to repair the cracked or missing grout in your bathroom. There is unsanded, sanded, epoxy, or acrylic grout and depending on the kind of tile that you will use the grout between, you will need to use one instead of the other. If you have marble tiles, you should not use sanded grout, since this will etch the marble irreparably. Use acrylic or unsanded grout on marble tiles.

Mix the grout according to the manufacturer’s instructions and before you go to replace the grout, the area should be cleaned with a mixture of water and vinegar. Use a grout saw to take out the damaged and loose grout, but be careful not to chip the tile. Dampen the joints with water and use a paper towel to soak up the water. The joints need to be filled up and the surface should be rounded out with a stick. Use a damp sponge to get rid of the excess.

Allow the grout to set firmly in the joints and the directions on the grout package should tell you how long this is going to take. A grout sealant should be applied over the grout after it dries, since this grout is going in an area that is going to be wet.

Clean the tile with a damp rag after the sealant dries and allow it to dry again. After the cloudy haze starts to appear on the tile, use a dry towel to polish this off.

You do not need to hire a professional to do these small home improvement jobs. Most of the time jobs of this size can be done by you and you will save a significant amount of money doing them on your own.


Jim Corkern is a writer and promoter of quality
New Jersey mold damage restoration and other states and cities such as
Connecticut mold remediation companies across the united states.

Protecting Your Deck From Water Damage

Waterproofing your deck that you worked so hard to pay for or to build is something that most homeowners need to do to keep their deck in good condition over the years. It will likely be used extensively and you want to keep it looking as good and as structurally sound as possible. Mold and rotting can occur to decks that are not properly waterproofed, so the deck’s structural integrity is also under scrutiny. Water from a pool or rain or snow can cause the water damage to your deck that you are trying to avoid, so applying a water sealant to the deck will help prevent all of this.

Waterproofing a new deck is not very different from waterproofing one that already exists on a property, but you should wait at least 30 days before you do, because the chemicals in the wood the deck was built with will need time to evaporate and the wood will need time to adjust to its new environment. After you have waited a month, you can start waterproofing the deck.

Clean off the entire deck and remove all furniture. It should be made completely bare and free of all debris, including leaves, sticks, pool toys, and etcetera. You can purchase a cleaner for the deck from most department stores. Follow the directions and apply it with a pump sprayer. When it starts foaming up, get a brush with stiff bristles and start scrubbing the surface of the deck firmly. This will not only remove all the dirt and other buildup from the deck, but also help to remove stains such as grease. After you are done, rinse all of the foam off with your garden hose or a few buckets of water. When you are doing this, you should be wearing eye protection.

Applying the sealant will be done with a roller or a pump sprayer and if there are any puddles of the sealant on the deck, you will have to roll them out so that the sealant coats the deck evenly.

Drilling a few small holes in your deck where water collects can also help further waterproof it. This will let the water drain off of the deck in these areas. They can be as big or as small as you want them to be, although 3/16 of an inch is about the smallest you can get that will allow for a decent amount of drainage.


Jim Corkern is a writer and promoter of quality
New Jersey mold damage restoration and other states and cities such as
Connecticut mold remediation companies across the united states.

Little known Phone Sticker Squeals On Water Damage And Voids Warranty

If you take a look inside the case of your cell phone, you should see a round white sticker placed somewhere on the device. What is it? This is called a water damage sticker and if your phone is exposed to moisture that makes its way inside the phone, this can be used to completely void your warranty, no matter the reason your phone may stop working. It does not seem to take much, either; a simple drop of water placed onto this sticker is enough to change its color and void the warranty on your cell phone. For honest consumers who accidentally get a small bit of water on their phone and then 5 or 6 months later, suddenly notice that the phone is having problems, knowing about this sticker is quite useful.

What exactly can you do to stop this little devil from voiding the warranty on your phone should is accidentally get a little damp? The best thing that you can do is to take a piece of satin finished scotch tape and put it over the sticker to keep the color from changing if it gets wet. If you drop your phone into the toilet or the bathtub, this probably isn’t going to be that effective, but if you are just worried about general moisture problems or an accidental quick spill of something on the phone, this should work just fine. If your phone stops working for some other reason, remove the tape and take it back to the manufacturer for repairs or a replacement.

It is was not exactly a bad idea for these stickers to be put on the inside of phones, though; a lot of phones get returned that are supposedly not water damaged, but are. At the same time, though, it is bad for the consumer because having such a sticker can completely void the warranty regardless of whether the liquid was the reason the phone stopped working or not. The phone could have just been a defective model and it would make no difference.

Hopefully people will use the information presented here honestly and not try to defraud the phone company into giving them a new item after their phone was irreparably damaged by having a hot cup of coffee spilled onto it or something like that. For honest consumers just having a bit of bad luck, it is great to know these kinds of things about our electronics just in case. Unfortunately, there are those that will attempt to misuse this information.



Garland Texas Water Damage Restoration
Blog has more related information free